RPW-031 – Single Spring for Mechanical Seals
RPW-031 – Single Spring for Mechanical Seals
Overview
The RPW-031 is a SINGLE COIL SPRING SEAL WITH ‘V’ PACKING – BI DIRECTIONAL.
Internal Wet Seal, Shrink Fitted Rotary Head, Parallel shaft V Packing. The design is a Bi-directional Single Spring with Set Screw Drive (Standard w/length).
Product Description
Technical Specifications
| Seal Shaft Sizes | 1.000″ – 4.000″ (12mm – 100mm) |
| Inboard Seal Face Combination | Car/TC and Car/SiC |
| Elastomers | V-Packing (PTFE) |
| Shaft Speeds | Up to 10 m/s |
| Pressures | Up to 8 barg (116 psig) – Shaft Size Specific |
Typical Applications & Industry Use Cases
The RPW-031 is a single-spring, internally mounted mechanical seal suited for general-purpose pumping and fluid-handling applications. Its simple spring-loaded design makes it reliable for clean or moderately clean fluids, moderate pressures, and standard operating speeds. This seal offers a compact, efficient, and cost-effective solution where heavy-duty sealing is not required.
Industries Served
Water supply and utility systems
clean water pumping, service water circulation, and domestic water systems.
Light industrial fluid transfer
solvents, light chemicals (subject to elastomer compatibility), general industrial liquids.
HVAC, building services, and auxiliary pumps
circulation, transfer, and service water duties.
OEM equipment and maintenance/retrofit pumps where a simple, easy-to-install seal is preferred.
Food, beverage, or light chemical processing (when elastomer/face materials are compatible with fluid characteristics).
Equipment & Use-Case Scenarios
- Small to mid-size centrifugal or horizontal pumps with shaft sizes and stuffing-box dimensions compatible with single-spring seals.
- Applications with clean or lightly contaminated fluids, minimal abrasives or solids, and steady operating conditions.
- Systems where ease of maintenance, quick replacement, or simplicity is valued over heavy-duty performance.
- Pumps operating under moderate pressures and temperatures consistent with single-spring seal ratings.
Why It Fits These Applications
- A single-spring design provides consistent sealing-face loading with fewer components, reducing the risk of installation errors and simplifying maintenance.
- Compact size makes it suitable for pumps with limited stuffing-box space or tight gland-envelope constraints.
- The simpler internal-seal construction is usually easier to fit, maintain, and replace than more complex multi-spring or cartridge-type seals.
- Cost-effective solution for general-duty pumps where heavy-duty sealing capacity is not required.
Installation Guidelines
Inspect and clean the shaft, seal bore or gland, and mating surfaces thoroughly before installation. Ensure there is no scoring, corrosion, or debris.
Gently slide the RPW-031 onto the shaft, ensuring proper seating of the spring and seal faces, and avoid damaging elastomer parts during installation.
Apply a light, compatible lubricant to elastomer surfaces to facilitate assembly, if needed.
Secure any drive components (e.g., set-screws or drive-sleeves) per specification, ensuring the seal is aligned and centred before final tightening.
After installation, start the pump under controlled conditions — check for leaks, vibration, or abnormal temperature rise before proceeding to full load.
Maintenance & Inspection Best Practices
- During routine shutdowns or maintenance intervals, inspect seal faces for wear, scoring, or glazing; check elastomers for hardening, swelling, or chemical degradation.
- Monitor pump alignment and shaft condition — misalignment or rough shaft finish accelerates seal wear.
- Keep a log of operating conditions — fluid type, temperature, pressure, run hours, start-stop cycles — to anticipate maintenance needs and detect abnormally short seal life.
- Proactively replace seals when signs of wear or aging appear, rather than waiting for complete failure, to avoid unplanned downtime.
- Ensure the pump fluid remains clean; avoid solid particles, abrasive media, or aggressive conditions that exceed the design limits of the single-spring seal.
Service & Support Options
- Material and elastomer selection guidance to ensure compatibility with fluid chemistry, temperature, and operating conditions.
- Spare parts availability — seal faces, elastomer components, drive parts — for quick turnaround during maintenance.
- Installation assistance to achieve optimal alignment, correct spring compression, and ensure leak-free commissioning.
- Preventive maintenance scheduling based on actual operating conditions, ensuring reliability and maximising seal lifecycle.
- Upgrade recommendations: if service demands increase (higher pressure, contaminated fluids, temperature variations), consider upgrading to more robust seal types (multi-spring, cartridge, bellows, or dual-seal).
Related Products
Contact HydroMax Seal
Contact HydroMax Seal today for innovative solutions, expert guidance, and over a century of engineering excellence. Your journey to mechanical sealing excellence starts with HydroMax Seal!
E-Mail: sales@hydromaxseal.com
Address: 18511 Beaumont Hwy Building D
Houston, TX
77049
